Home > Tool Shop > Hardware and Consumables > Wipes and Cleaning

Everbuild CEMSTRIP Environmentally Friendly Mortar Concrete Stain remover 1L

Everbuild CEMSTRIP Environmentally Friendly Mortar Concrete Stain remover 1L
Everbuild CEMSTRIP Environmentally Friendly Mortar Concrete Stain remover 1L
Everbuild CEMSTRIP Environmentally Friendly Mortar Concrete Stain remover 1L
Stock Code CEM1

£3.99 Inc VAT

£3.33 Ex Vat

Everbuild
In Stock - available for next day delivery
Stock Checked:
Quantity
Loading Updating parcel...
Estimated UK Delivery Costs - Per Order
Standard Delivery £2.95
Next Day Delivery £5.95
Royal Mail Logo

Small Product

More Information
International Delivery Options Available

Everbuild Cemstrip is a new type of cement, concrete and mortar stain remover that provides a more environmentally friendly and safer alternative to conventional hydrochloric acid based cement removers. Cemstrip will also remove salts and efflorescence from the surface of mineral substrates and is a very effective general cleaner for removing ingrained dirt, grease and stains from paths and patios. Cemstrip is a highly concentrated formula that can be diluted by up to 10 times with water to suit a variety of applications. Unlike hydrochloric acid based products Cemstrip can be safely used on most metal surfaces such as tools, cement mixers and other building equipment. Cemstrip is Non-hazardous in storage, transport and usage. It is also fully biodegradable.

USES
Removes cement, mortar and concrete on most mineral
surfaces such as paths, patios and walls.
Cleaning tools, cement mixers and other building
equipment.
CHARACTERISTICS / ADVANTAGES
Available in bottles or as a ready-to-use spray.
Water clean-up.
Economical, makes up to 10 times the volume of the
bottle when diluted.

APPLICATION INFORMATION
Yield Approx. 10m2 per litre depending on porosity of substrate.

APPLICATION INSTRUCTIONS MIXING
9 parts water to 1 part EVERBUILD CEMSTRIP® –
Cleaning general stains and ingrained dirt from paths, patios and horizontal surfaces.
2 parts water to 1 part
EVERBUILD CEMSTRIP® – Cleaning light mortar stains from paths, patios, walls
or vertical surfaces.
Product Data Sheet
EVERBUILD CEMSTRIP®
May 2018, Version 01.01
020405030040000014 1 / 3
1 part water to 1 part EVERBUILD CEMSTRIP® – Cleaning
heavy mortar stains from walls or vertical surfaces.
Neat – Cleaning tools, cement mixers and other building
equipment.
SUBSTRATE PREPARATION
When cleaning paths, patios, cement stains etc. from
surfaces always thoroughly wet surfaces prior to application.
Do not apply to a dry surface.
Always test a small inconspicuous area prior to full application.
When cleaning tools and equipment pre-wetting is not necessary.
APPLICATION
General Cleaning:
Moisten surfaces with water and apply EVERBUILD
CEMSTRIP® with brush or low pressure spray (avoiding mist formation) from the top of the area downwards.
Leave for 5-10 mins then scrub/wash off with a hose,
brush or power washer until the surface is clean. Never
allow the product to dry on surfaces. Where a
second application is necessary, repeat the procedure
above.
Cleaning tools/equipment:
EVERBUILD CEMSTRIP® will remove fresh cured cement
and wet or semi-cured cement from tools. Spray
onto item in question. Leave for 15 mins to act (light
stains) or up to 3 hours for heavy contamination.
Wash off the product with clean water. Use of a scourer will
assist removal of stubborn stains.
Use a hot power
wash to assist removal of staining from mixing equipment.
After removal, always spray tools with Everbuild®
XT44 Maintenance Spray (or any other proprietary
maintenance spray) to prevent further
corrosion/rust.
LIMITATIONS
Do not use on marble, granite or travertine.
Do not use on coloured cement-based pavers.
Always test a small inconspicuous area prior to full application, especially on coloured flags/stones.
Do not use on soft metals such as lead brass, copper
or aluminium.
Do not apply to dry surfaces or allow Cemstrip® to
dry on the surface.
Always thoroughly rinse equipment to prevent further
rusting/corrosion.
Avoid overspray on sensitive surface such as brass,
copper, stainless steel and aluminium.
Remove any excess material or spills immediately with clean fresh
water.
Cleaning mortar or concrete from tools – the
stronger or older the mix, the more difficult it will be to remove.
Always wash out spray equipment immediately after use with clean fresh water.
It is the user’s responsibility to determine suitability for use.
If in doubt contact technical services for advice.

EAN 5029347611019