Categories

  • No categories

A sample text widget

Etiam pulvinar consectetur dolor sed malesuada. Ut convallis euismod dolor nec pretium. Nunc ut tristique massa.

Nam sodales mi vitae dolor ullamcorper et vulputate enim accumsan. Morbi orci magna, tincidunt vitae molestie nec, molestie at mi. Nulla nulla lorem, suscipit in posuere in, interdum non magna.

DeWalt DW712 110 Volt Sliding Compound Mitre Saw 110v with 240v 3.3kva Carroll and Meynell Transformer

DeWalt DW712 110 Volt Sliding Compound Mitre Saw 110v with 240v 3.3kva Carroll and Meynell Transformer
DeWalt DW712 110 Volt Sliding Compound Mitre Saw 110v with 240v 3.3kva Carroll and Meynell Transformer
DeWalt DW712 110 Volt Sliding Compound Mitre Saw 110v with 240v 3.3kva Carroll and Meynell Transformer
Stock Code DW712_CONVERT

£393.89 Inc VAT

£328.24 Ex Vat

Dewalt
Product not in stock
This product has no direct replacement

The new DW712 corded compound slide mitre saw is the most accurate saw the company has ever manufactured. It delivers an accuracy of less than 0.1°, as a result of new manufacturing techniques, higher fences for greater material support, adjustable scales and a new, patented, mitre and bevel detent system.

The DW712 is also the first 216mm portable mitre saw to be able to cut a 60° mitre improving cutting angle performance on stairs and roof joints

The new saw has a horizontal dual rail slide extending its capacity to 300x 70mm. This dual rail slide system also makes it possible for grooving applications to be completed such as those in lap joints and door linings.

The new manufacturing techniques have achieved a significant improvement in base/fence perpendicularly and head alignment, which leads to a superior finish and unparalleled levels of accuracy.

Every DW712 is individually and comprehensively tested before it leaves DeWalts Perugia factory, with the test results recorded against its serial number.

The DW712 has a 1600W motor delivering an output of 930W and providing superior power in high torque applications. Its electronic speed regulator controls power delivery with high torque for low speed applications.

Can't get a 240v? This 110v mitre saw comes complete with a twin outlet transformer.

Primarily for use when using portable electric tools on outdoor sites.

- Manufactured to BS3535
- Thermal overload protection
- BS4343 output sockets as standard
- Glass reinforced polyester case
- Input flex and 13 amp plug
- Transformer completely encapsulated for extra weatherproofing

These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVA

Primarily for use when using portable electric tools on outdoor sites.

Tool Rating 3300 VA.
Output Sockets. 2 x 16amp.

- Manufactured to BS3535
- Thermal overload protection
- BS4343 output sockets as standard
- Glass reinforced polyester case
- Input flex and 13 amp plug
- Transformer completely encapsulated for extra weatherproofing

These transformers are rated for intermittent operation at their maximum listed power capability for a duty cycle of 25%. I.e. 5 minutes ON 15 minutes OFF. They may be used in a continuous operation mode at a rating of 50% of their maximum capability. E.g. a 3.3KVA unit may be operated continuously at 1.65KVA

Transformer Specifications:

Input 240 volts 50Hz single phase. Complete with 2 metres of 3-core flexible cable to BS6500 for connection to mains supply and a 13 amp plug.

Output 110 volts. Centre tapped and earth screen between primary and secondary windings which is bonded to the centre tap of the secondary winding, the earth pin on each output socket and earth core of the mains input plugs and sockets.

BS4343 flush type sockets with spring flap covers fitted as standard. Units are protected by suitably rated thermal overload cut-outs.

Portable Tool Transformer - Safety Instructions
1. The transformer will get warm in normal use, make sure that the heat will not damage any floor covering that it is standing on. It is not advisable to place the transformer onto carpet, vinyl floor covering, etc., and use at continuous rating for any length of time.

4. Although the transformer may be of insulated construction, it is not double insulated (class 2) and the earth pin of the output socket must be connected to the centre point of the secondary winding and to the transformer incoming earth.

2. The transformer may be fitted with an over temperature cut-out switch, in the event of this operating, let the unit cool down then reset the cut-out switch before using again.

5. Power tool transformers must not be tested as class 2 appliances on portable appliance testers, flash test only at 1.5 KV.

3. Check the transformer power rating against the power rating of the tool you are going to use. The transformer can supply portable tools in normal use up to the rating shown on the transformer and consultation with the above table. Care should be taken when using the transformer to supply constant loads, i.e. floodlights, wallpaper strippers etc. The transformer can only supply about half of its rated power to continuous load like this.

6. Power tool transformers have an inherent high inrush current, in the event of the fuse blowing on switch, check that the fuse in the input plug is suitably rated and is of the anti surge type. Miniature circuit breakers protecting the sockets should have a type 4 tripping characteristic.

EAN